316L (Stainless Steel Balls)

AISI type 316L stainless steel balls meet requirements for an unhardened ball with excellent toughness and resistance to corrosion. Corrosion resistance may be increased through annealing. Both non-annealed and annealed balls are widely used in valves and related equipment.

Type 316L is a low carbon austenitic, chromium-nickel-molybdenum stainless steel with general corrosion resistance similar to type 316, but with superior resistance to intergranular corrosion following welding or stress relieving.

It is suggested for use in certain corrosive environments for parts that are fabricated by welding and cannot be subsequently annealed. Parts made from 316L are generally limited to service temperatures up to 800ºF (425ºC).

Click here for sizes and pricing

316L Stainless Steel Balls: Available Grades and Sizes
Grade	Size Range in Inches and Millimeters
100 - 200 - 1000	1/8 - 2 3.175 - 50.800

Balls Pound
Size		Balls Pound
Inches	Millimeters	Balls Pound
1/8	3.175	3,420
5/32	3.968	1,750
3/16	4.762	1,010
7/32	5.556	638
1/4	6.350	427
9/32	7.143	300
5/16	7.9.7	219
11/32	8.731	164
3/8	9.525	127
13/32	10.318	99.6
7/16	11.112	79.7
15/32	11.906	64.8
1/2	12.700	53.4
17/32	13.493	44.5
9/16	14.287	37.5
19/32	15.081	31.9
5/8	15.875	27.4
21/32	16.668	23.6
11/16	17.462	20.6
23/32	18.256	18.0
3/4	19.050	15.8
25/32	19.843	14.0
13/16	20.637	12.5
27/32	21.431	11.1

Balls Pound
Size		Balls Pound
Inches	Millimeters	Balls Pound
7/8	22.225	9.97
29/32	23.018	8.97
15/16	23.812	8.10
31/32	24.606	7.35
1	25.400	6.68
1 1/8	28.575	4.69
1 1/4	31.750	3.42
1 3/8	34.925	2.57
1 1/2	38.100	1.98
1 5/8	41.275	1.56
1 3/4	44.450	1.26
1 7/8	47.625	1.02
2	50.800	.844


	Material Analysis: All sizes and grades are of the highest quality and in accordance with AISI type 316L. Passivation to ASTM A380 is available upon request..

Material	AISI	Federal	Military	ASTM	UNS	AMS
Stainless Steel Type 316L	316	QQ-S-763	-	A-493	S-31603	-

Chemical Analysis
Carbon................................................................	0.03% maximum
Chromium...........................................................	16.0% to 18.0%
Manganese.........................................................	2.0% maximum
Silicon..................................................................	1.0% maximum
Nickel	10.0% to 14.0%
Phosphorus.........................................................	0.045% maximum
Sulphur................................................................	0.03% maximum

Mechanical Properties Hardness as measured on parallel flat surfaces is Rockwell “C” 25-39.
Tensile Strength..................................................	80,000 to 120,000 psi
Elongation in two inches....................................	10.0% to 15.0%
Reduction in area................................................	55.0% to 65.0%
Modulus of elasticity...........................................	28,000,000 psi
Density.................................................................	0.29 lbs./cu. in